Versión 2.82

03.05.2023

• Preview of values in a route tree (see manual Route / Route Tree)
• Difference form last and reference values in route (see manual Route / Last and reference values)
• Angles Counting marks (with or against rotation) (see manual MENU / SETTINGS / Global Settings / Angles Counting)
• Oversampling (higher sampling frequency defined by user) (see manual Analyzer / Edit Measurement / Sampling Freq)
• New frequency ranges in octave spectrum (see manual Octave Analysis / Measurement Settings / Frequency Range
• Finishing Averaging (see manual Analyzer / Edit Measurement / Avg)
• Time axe unit in degrees (see manual Analyzer / Graph Properties / Time Axe Unit)
• External trigger edge and level removed from trigger menu and united with tacho sensor (see manual MENU / SETTINGS / Tacho / External)
• Sensors list import (see manual MENU / SETTINGS / AC Sensors / Sensors list import)
• Delta cursor value initialized according to the speed (see manual Analyzer / Graph Properties / Cursor)
• Retrig in route (see manual Route / Route Meas Mode)
• Export a record to csv (see manual Recorder / Project Menu / Export to csv)
• Report for advanced balancer (see manual Advanced Balancer / Balancer Menu / Balancing Report)

Versión 2.81

22.12.2022

• Angles (phases) with or against rotation (see manual MENU / SETTINGS / Global Settings / Angles Counting)
• Balancing: new design and terminology (see manual Balancer)
• Balancing: operating speed parameter (see manual Balancer / Rotor Settings / Operating Speed)
• Balancing: trial weight position (see manual Balancer / Single Plane Balancing / Trial Run)
• Balancing: more than 255 values in averaging available
• Advanced Balancing: trial weight position (see manual Advanced Balancer / Balancing Procedure / Trial Runs)
• Sensor's name added to csv export (see manual Analyzer / Meas Menu / Export to csv)
• Canceled restrictions of highest sampling frequency (see manual Analyzer / Edit Measurement / Band fmax)

Versión 2.80

09.06.2022

• Frf format (see manual Analyzer / Graph Properties / Frf Format)
• Flat top window (see manual Analyzer / Edit Measurement / Window)
• The lin / log / dB choice for overall value (see manual Analyzer / Graph Properties / Axe y)
• MCSA: thd shown in table (see manual MCSA / MCSA Screen / Frequency table and thd)
• Continual saving in Route (see DDS manual)

Versión 2.79

16.02.2022

• New runup trigger mode - asap all (see manual MENU SETTINGS / Trigger Settings / Runup Trigger Mode)
• The user entered frequency in amp+phase measurement (see manual Analyzer / amp+phase)
• Editable basic meas list (see manual Analyzer / Meas Menu / New Basic)
• Notes in csv header (see manual Analyzer / Meas Menu / Export to csv)
• Polar graph in balancer (see manual Balancer / Single Plane Balancing / Run 1)

Versión 2.78

26.07.2021

• 16 bit wav encoding (see manual MENU / SETTINGS / Global Settings / Wav Encoding)
• Limits multipliers (enables to increase or decrease limits) and Acc fmin in FASIT (see manual FASIT / FASIT Settings)
• Adash limits enabled for velocity measurement with fmin lower than 10 Hz (see manual Analyzer / Meas Menu / Limits / Adash Limits)
• Adash limits enabled for acceleration measurement with fmin higher than 500 Hz (see manual Analyzer / Meas Menu / Limits / Adash Limits)
• IR Camera warming up (see manual IR Camera / Warming Up)

Versión 2.77

01.07.2021

• IR Image Correction (see manual IR Camera / IR Image Correction)

Versión 2.76

19.05.2021

• Limit values for static measurements (see manual Analyzer / Meas Menu / Limits)
• New measurement type - complex Smax (see manual Analyzer / Complex Smax)
• Minimum and Maximum values during averaging (see manual Analyzer / Edit Measurement / Avg)
• ADS: changing channel without losing readings (see manual ADS / ADS Settings / Measurement Definition)
• New feature - Stethoscope easily accessible from Menu / Stethoscope

Versión 2.75

02.02.2021

• Runup minimum and maximum speed (see manual Global properties / Trigger Settings)
• Negative Averaging (see manual Global properties / Trigger Settings / Negative Averaging)
• Negative Averaging in Bump Test (see manual Bump Test / Settings / Negative Averaging)
• Balancer: circumferential distance of balancing mass (see manual Balancer / Single plane balancing / RUN2 - the RESULT Screen)
• Route status symbols like VA3 (✓, !, .) (see manual Route / Route Status)
• Marking of non-exported routes (see manual The Route / Route measurement)
• Battery percent in About dialog (see manual Global properties / The About...)
• Export bump test to analyzer (see manual Bump Test / Analyse)

Versión 2.74

23.11.2020

• New "Advanced Balancer" module (see manual Advanced Balancer)

Versión 2.73

15.07.2020

• Adjustable Limits in the route (see manual Route / Limits)
• IR Camera: Calibration (see manual IR Camera / Buttons / Calibration)
• Balancer: Unbalance value displayed (see manual Balancer / Single Plane Balancing)
• Balancer: The "Remove trial" item in basic settings menu (see manual Balancer / Basic Settings)
• ADS: Vibration scale in animation (see manual ADS / ADS Settings / Vibration Scale)
• ADS: Zoom and move using touch screen (see manual ADS / Buttons for Machine View / Zoom)

Versión 2.72

25.05.2020

• Adjustable order in amp+phase measurement (see manual The Analyzer mode / amp+phase measurement)
• Adjustable order in phase shift measurement (see manual The Analyzer mode / Phase shift measurement)
• Adjustable resolution in orders measurement (see manual The Analyzer mode / orders measurement)

Versión 2.71

28.04.2020

• Calculator (see manual MENU / Run / Calculator)
• Physical unit and frequency range in bump test (see manual Bump Test / Settings)
• Graph unit for spectra (see manual Analyzer / Graph Properties / Graph Unit)
• Screenshots in lossless png format instead of jpg (see manual MENU / RUN / Screenshot
• Bearing fault frequencies: BSF2 instead of BSF (see manual Analyzer / Graph Properties / Bearing Faults)
• Back and Forward buttons in Help window (see manual MENU / RUN / Help)

Versión 2.70

13.12.2019

• MCSA module (see manual MCSA)
• Adjustable FASIT limits (see manual FASIT / Setup)
• Sensor's name (see manual MENU / Settings / AC sensors / Name)
• Value type (RMS, 0-P, P-P) defined globally (see manual MENU / SETTINGS / Spectrum Settings / Detect Type)